Multimode LC SX 0.9mm 2.0mm Fiber Optic Connectors

Simplex duplex LC SX 0.9mm 2.0mm 3.0mm multimode fiber optic connectors

LC connector first. LC (Lucent Connector) was first developed by Lucent Technologies as a response to the need by their primary customers for a small and low insertion loss connector. Then the LC design was standardized in EIA/TIA-604–10 and is offered by other manufacturers. The ferrule size of an LC connector is 1.25 mm, half the size of SC connector ferrule. LC connector is rated for 500 mating cycles and its typical insertion loss is 0.25 dB. There are solid reasons that LC connector is a preferred connector type for high-performance network. LC connector has a small size, it borrows split-sleeve construction and a cylindrical ferrule (usually ceramic) from SC connector, and it can have a push-and-latch design providing pull-proof stability in system rack mounts.

ST/PC ST/UPC ST/APC Simplex Duplex Single mode Multimode Fiber Optic Patch Cord is designed with high performance hybrid or single type connector and used for network applications. Its optical performance has been 100 % tested (Insertion Loss, Customer specified length and Return Loss). This fiber optic patch cord is available in standard colors like Yellow, Orange, Aqua or Purple and other colors are available upon request. The cable outer jacket is available in PVC, Low Smoke Zero Halogen (LSZH) and PC, UPC, APC connector type are available. It has a high concentricity of 0.098 in (2.5 mm) ceramic ferrule for FC, ST, SC and 0.049 in (1.25 mm) ceramic ferrule for LC and MU. It provides customer satisfied requirements.

Fiber optic connectors are used at both ends of a fiber jumper to achieve cross connections of fibers. There are many types of connectors developed for fiber optic jumper cables. For example, single-mode networks have used FC or SC connectors in about the same proportion as ST and SC in multi-mode installations. To choose a proper fiber optic patch cable, fiber optic connector is a very important factor to consider. LC connector is a common connector type used in fiber optic jumper cables. An LC to LC fiber patch cable is a patch cable terminated at both ends with LC connectors. The following text gives a detailed introduction of LC to LC fiber patch cables.

Standards Compliance

. Telcordia (formerly Bellcore) GR-326-CORE Generic requirements for Single mode
optical connectors and Jumper assemblies.
. IEC 874-1 Generic specification for fiber optic connectors and cables
. ANSI/TIA-568-C.3, ISO/IEC 11801 2nd Ed., CENELEC EN 50173, UL94V-0
. Cable flame resistant rate: OFNR or IEC60332-3 standard

Features

. 100% tested on optical performance (Insertion Loss
Customer specified length & Return Loss)
. Standard colour is Yellow, Orange, Aqua or Purple,
other colours available upon request
. Cable outer jacket available in PVC, Low Smoke Zero Halogen (LSZH)
. PC, UPC, APC connectors type available
. High concentricity 2.5mm ceramic ferrule for FC, ST, SC
and 1.25mm ceramic ferrule for LC and MU
. Available in G652D, G657A, OM1, OM2, OM3 and OM4
. Position A/Position B markings
. Available in 0.9mm, 1.6mm, 2.0mm, 3.0mm sizes

APPLICATIONS

· CATV
· Active device termination
· Telecommunication networks
· Metro
· Local Area Networks (LANs)
· Data processing networks
· Test equipment
· Precise installations
· Wide Area Networks (WANs)
· Industrial, medical & military

FEATURE

· Low insertion loss and back reflection
· One-piece construction and pull-proof design
· Free-floating pre-radiuses ceramic ferrule
· Precision anti-rotation key and Corrosion resistant body
· Variety of boot types and colors

APC Connector is a type of fiber connector that minimizes backreflection due to a 5° to 15° angle-polish applied to end faces. Like illustrated in the following picture.

Angle-polished connectors should only be mated to other angle-polished connectors. Mating to a non-angle polished connector causes very high insertion loss. Generally angle-polished connectors have higher insertion loss than good quality straight physical contact ones.
“Ultra” quality connectors may achieve comparable back reflection to an angled connector when connected, but an angled connection maintains low back reflection even when the output end of the fiber is disconnected .

Angled-polished connections are distinguished visibly by the use of a green strain relief boot, or a green connector body. The parts are typically identified by adding “/APC” to the name.
For example, an angled FC connector may be designated FC/APC, an angled LC connector may be designated LC/APC, etc.

The value of return loss for mated APC connectors in the field will typically be greater than -65 dB. For a UPC connection, it is normally -55 dB.
When connectors are unmated—such as unused ports in an FTTP distribution frame—the return loss for APC connectors is -65 dB or greater, compared to UPC connectors that will be in the neighborhood of 14 dB.

Features:

► Complies with IEC 61754-20 and TIA 604-2

► Low insertion loss and back reflection

► Bayonet shaped housing for easy termination

► Nickel plated brass body

► Zirconia ceramic ferrule with high end PC finish

► RoHS, REACH SvHC compliant

Applications:

► Local area networks

► Data processing networks

► Distribution application

► Premises distribution

► Test and laboratory equipmen

Ease of use

Parameter

more connector for reference 

How to order

1. Connector type : SC / FC / LC / ST / MPO / MTP / MU / MTRJ / E2000 / SMA
2. Mode type : single mode ( UPC and APC ) / multi mode ( PC )
3. Cable diameter : 0.9 / 2.0 / 3.0 mm ( can customized other diameter )
4. Coating material : PVC / LSZH
5. fiber count : simple / duplex / 4 core / 6core / 8 core /12 core / 24core/48 core / 96 core and so on
6. Cable type : G652D / G657A1 / G657A2 /G655 / OM1 / OM2 / OM3-150 / OM3-300 / OM4 /OM5
7. Patch cord length : according to your requirement
8.MPO/MTP connector should let us know which method ( A type / B type /C type ), male or female , fiber count (4/8/12/16/24/32 fiber )